Doug any recommendations for a relay that I can use for the load 1 output which is 3.3volts?
3.3v trigger 36v from the power supply
or
3.3 trigger 24v after the convertor
Solid state relay?
Search found 25 matches
- Sun Jun 14, 2020 10:04 pm
- Forum: Buildbotics Tech Support
- Topic: Load1 36v down to 12v
- Replies: 4
- Views: 5012
- Mon Jun 08, 2020 10:41 pm
- Forum: Feature ideas
- Topic: Extra Offsets
- Replies: 6
- Views: 19422
Re: Extra Offsets
I'm in the middle of upgrading my whole machine, so haven't had a chance yet to try the VFD or my new spindle, I'll come back and report once Im up and running in a few weeks
- Sun Jun 07, 2020 9:51 pm
- Forum: Feature ideas
- Topic: Extra Offsets
- Replies: 6
- Views: 19422
Re: Extra Offsets
Yes that will work Hopefully there will be a minimum of say 6? buttons we can configure to our liking? Be good to also name the buttons if that's possible? More the better really 1 Offset 2 Offset 3 Offset 4 probe Z only 5 Probe XYZ 6 Spare 7 8 9 10 Looking forward to the next release Thanks Doug fo...
- Sun Jun 07, 2020 4:16 pm
- Forum: Feature ideas
- Topic: Extra Offsets
- Replies: 6
- Views: 19422
Re: Extra Offsets
Doesn't have to be to fancy, I generally have a permanent jig for my coaster engraving JOB1 I have a sheet of bronze anodized aluminum JOB2 Then black anodized aluminum JOB3 And a general position for "other" jobs JOB4 Be handy to set each XY 0 for each JOB and save it and when I need to move to say...
- Sat Jun 06, 2020 5:18 pm
- Forum: Feature ideas
- Topic: Extra Offsets
- Replies: 6
- Views: 19422
Extra Offsets
Hi Doug,
A lot of the time I have 3 or even 4 jobs on the cnc table at any one time.
Having a pull down list of offsets would be handy.
Mick
A lot of the time I have 3 or even 4 jobs on the cnc table at any one time.
Having a pull down list of offsets would be handy.
Mick
- Wed May 20, 2020 4:56 pm
- Forum: Buildbotics Tech Support
- Topic: Load1 36v down to 12v
- Replies: 4
- Views: 5012
Re: Load1 36v down to 12v
Thanks Doug
- Tue May 19, 2020 7:23 pm
- Forum: Buildbotics Tech Support
- Topic: Load1 36v down to 12v
- Replies: 4
- Views: 5012
Load1 36v down to 12v
So I'm upgrading to a 2.2kw water cooled spindle and was thinking of using the load1 output to turn on and off the water pump. My controller is currently powered by a 36volt power supply The water pump is 12volt My thoughts were to run the load1 output to a step down converter as below https://au.mo...
- Tue Mar 31, 2020 9:18 pm
- Forum: Buildbotics Tech Support
- Topic: Unable to upload gcode
- Replies: 11
- Views: 14411
Re: Unable to upload gcode
Ive just had a bit of a poke around, and found that after deleting all the files in /upload and reloading them from the USB their was a added / "backslash" to the files (2) so I deleting those again and removed any special characters from the file names which I had a "#" and could upload them just f...
- Tue Mar 31, 2020 8:26 pm
- Forum: Buildbotics Tech Support
- Topic: Unable to upload gcode
- Replies: 11
- Views: 14411
Re: Unable to upload gcode
Doug I'll have to re-open this issue, I'm having the same issue again, Ive tried reformatting my usb, re did the tool paths, but I still cant upload any new files, I know the files are good, Ive ran them from the usb in cammotics and it runs fine, so has something with the buildbotics controller sin...
- Mon Mar 16, 2020 5:37 pm
- Forum: Buildbotics Tech Support
- Topic: Unable to upload gcode
- Replies: 11
- Views: 14411
Re: Unable to upload gcode *solved*
All sorted looks like it was a corrupt folder/files. All my other files on the usb would load fine soI redid the tool paths and put the files in the / of the usb and it uploaded just fine.