I'm getting the indication for an upgrade to v.1.0.2 but nothing happens when I click the upgrade button. I'm sure I'm missing something here. Could someone fill me on where I'm going wrong? I'm pretty sure V.1.0.0 went in without a hitch.
Thanks
Search found 11 matches
- Wed Mar 30, 2022 3:26 pm
- Forum: Buildbotics Tech Support
- Topic: V.1.0.2
- Replies: 6
- Views: 12545
- Tue Jul 13, 2021 4:50 pm
- Forum: Buildbotics Tech Support
- Topic: Control 'Un-homing' itself
- Replies: 15
- Views: 12722
Re: Control 'Un-homing' itself
Hey Alex, it sounds like we have similar situations. I have a shop with 'spoty' wifi. I have the recommended antenna and I still have problems maintaining a connection. I'm using a cheap internet switch connected between my laptop and the controller's internet port (and no connection to my router). ...
- Mon Jul 12, 2021 4:28 pm
- Forum: CNC Machine Retrofits
- Topic: MillRight CNC Mega V XL
- Replies: 4
- Views: 17618
Re: MillRight CNC Mega V XL
So are any of you Mega V owners using it as a plasma cutter? If so, how well does it cut?
- Wed Jun 16, 2021 6:07 pm
- Forum: Buildbotics Tech Support
- Topic: Gcode not being updated after a save
- Replies: 0
- Views: 19851
Gcode not being updated after a save
I'm running into an issue with my settings not being updated after a save every time. Here's an example. I made the change that is circled and saved. Then ran the gcode and I get the error in the second figure. I tried saving several times with no improvement. Then I restarted the controller and I w...
- Mon Jun 07, 2021 9:43 am
- Forum: Frequently Asked Questions
- Topic: How does probing work?
- Replies: 17
- Views: 60430
Re: How does probing work?
Alex, thanks for the update.
- Fri Jun 04, 2021 5:19 pm
- Forum: Frequently Asked Questions
- Topic: How does probing work?
- Replies: 17
- Views: 60430
Re: How does probing work?
Hey Alex, my situation is nowhere near as complicated as yours but I did want to be able zero off the material or machine bed whenever I needed to. I'm learning gcode just like you but I started with Doug's code and added a few lines that seem to get the job done. All the code below assumes I'm zero...
- Fri Jun 04, 2021 4:49 pm
- Forum: Buildbotics Tech Support
- Topic: Static IP address for wifi and ethernet
- Replies: 3
- Views: 9958
Re: Static IP address for wifi and ethernet
I was afraid you were going to say that. I've got an older router and it doesn't support that capablility. I've got lot's of cameras and 2 NVRs on the network and I'd rather not take the time right now configuring a new router. I'll keep it in mind when I replace the router. Thanks for the reply. r
- Wed Jun 02, 2021 5:02 pm
- Forum: Feature ideas
- Topic: feed (speed) over ride
- Replies: 3
- Views: 15476
Re: feed (speed) over ride
I'll vote for this feature also. Of all the things I miss most about using Mach 3 is this ability. It comes in handy when making your first pass over a rough surface and you need to slow down for the random irregularities.
- Wed Jun 02, 2021 7:29 am
- Forum: Buildbotics Tech Support
- Topic: Static IP address for wifi and ethernet
- Replies: 3
- Views: 9958
Static IP address for wifi and ethernet
Is there a way to set a static IP address for both wifi and ethernet ports? My wifi is really slow in my shop and I've setup a switch between my laptop and BB controller to use when I can't get things to update through wifi. The ethernet address seems to stay the same (169.254.162.169) since I've se...
- Thu May 06, 2021 9:54 am
- Forum: Announcements
- Topic: Version 1.0.0 Released
- Replies: 8
- Views: 25270
Re: Version 1.0.0 Released
Another little problem... when I opened by gcode job, the code didn't display but my test macro button code showed in it's place.
https://www.dropbox.com/s/bkcgf31ggrpex ... M.jpg?dl=0
The file name is correct, it cuts correctly but no 3d simulation.
https://www.dropbox.com/s/bkcgf31ggrpex ... M.jpg?dl=0
The file name is correct, it cuts correctly but no 3d simulation.