Search found 352 matches
- Mon Nov 18, 2019 4:51 pm
- Forum: Post Processors
- Topic: Vectric Post Processor
- Replies: 15
- Views: 40921
Re: Vectric Post Processor
It seems that my post processors are not fully compatible with older versions of Vectric software. They fail on stuff related to water jet control. So, I created two new posts called buildbotics_no_jet_inch.pp and buildbotics_no_jet_mm.pp . They are now available on github at https://github.com/buil...
- Sun Nov 17, 2019 1:56 pm
- Forum: Buildbotics Tech Support
- Topic: PWM -> 0-10V adapter
- Replies: 6
- Views: 9330
Re: PWM -> 0-10V adapter
This is the first time I've seen the particular spindle and power supply that you are using. The PWM to 0-10V converter that you referenced will probably work, but the information provided is a little unclear. The Buildbotics Controller puts out a 3.3V PWM signal. The PWM output frequency from the B...
- Sun Nov 17, 2019 8:21 am
- Forum: Post Processors
- Topic: general question
- Replies: 1
- Views: 16570
Re: general question
LinuxCNC, however we do not support the complete set. The "Cheat Sheet" page on the BB controller describes the GCodes that are supported. In addition, it provides hypertext links to the specification for the specific GCodes. Those links go to the LinuxCNC documentation. Also, if you create a new po...
- Wed Nov 13, 2019 3:07 pm
- Forum: Buildbotics Tech Support
- Topic: VFD/Spindle causing Controller to Crash
- Replies: 3
- Views: 6811
Re: VFD/Spindle causing Controller to Crash
When we last spoke, he reported that he rerouted his spindle cable to separate it from the power cable serving the Buildbotics Controller and the problem went away.
- Wed Oct 30, 2019 9:08 pm
- Forum: Feature ideas
- Topic: Raspberry Pi 4B
- Replies: 1
- Views: 11378
Re: Raspberry Pi 4B
Thank you for the suggestion. We have looked briefly at the RPi 4. One problem it that they moved the connectors on the RPi 4 from where they were on the RPi 3, so we can't just change them out without changing our back panels. Aside from that, we're told that the 4 runs a bit hotter than the 3 and ...
- Thu Oct 17, 2019 9:18 am
- Forum: Post Processors
- Topic: Vectric Post Processor
- Replies: 15
- Views: 40921
Re: Vectric Post Processor
Thanks for pointing this out, Mick. The correct link is:
https://github.com/buildbotics/buildbot ... -processor
I also corrected the first posting that you responded to.
https://github.com/buildbotics/buildbot ... -processor
I also corrected the first posting that you responded to.
- Wed Oct 16, 2019 12:09 pm
- Forum: Post Processors
- Topic: Vectric Post Processor
- Replies: 15
- Views: 40921
Vectric Post Processor
Vectric has created a Post Processor for the Buildbotics Controller. It will be included in future releases of their products. For existing and older Vectric products, you can get it from github at https://github.com/buildbotics/buildbotics-vectric-post-processor . Please report your experiences wit...
- Wed Oct 16, 2019 11:54 am
- Forum: Post Processors
- Topic: Fusion 360 Post Processor
- Replies: 18
- Views: 55324
Fusion 360 Post Processor
We have a post processor for Fusion 360 on GitHub. You can get it at https://github.com/buildbotics/buildbot ... on360-post . Please report any problems you encounter in this forum.
- Wed Oct 09, 2019 10:06 am
- Forum: Feature ideas
- Topic: Enable Stepper Motors
- Replies: 2
- Views: 10619
Re: Enable Stepper Motors
We do not have a command to do this. However, all the motors get tuned off when the machine goes into estop. You could click the estop button. Beware that estop clears all position information so you will have to re-home the machine after the estop clears.
- Wed Oct 09, 2019 10:02 am
- Forum: Feature ideas
- Topic: Do away with "offset"
- Replies: 4
- Views: 19628
Re: Do away with "offset"
I have submitted a new issue on github asking for this change. You can see the issue (and add to it if you like) on github. The issue can be viewed at the following link.
https://github.com/buildbotics/bbctrl-f ... issues/227
Doug
https://github.com/buildbotics/bbctrl-f ... issues/227
Doug