Hmmm..
Is the machine going outside the envelope that is defined by the soft limits?
Search found 352 matches
- Fri Sep 30, 2022 7:02 pm
- Forum: CNC Machine Retrofits
- Topic: Micro Kinetics / Sherline Benchtop Lathe
- Replies: 8
- Views: 16643
- Mon Sep 19, 2022 3:31 pm
- Forum: CNC Machine Retrofits
- Topic: Micro Kinetics / Sherline Benchtop Lathe
- Replies: 8
- Views: 16643
Re: Micro Kinetics / Sherline Benchtop Lathe
Thanks for your work on this.
- Sun Jul 31, 2022 8:50 pm
- Forum: Buildbotics Tech Support
- Topic: Sherline Spindle Tachometer & Speed Control
- Replies: 4
- Views: 10509
Re: Sherline Spindle Tachometer & Speed Control
At present, the BB Controller does not have the ability to read (and make use of an analog input signal). The hardware is in place, but no software to use it. Systems using a Variable Frequency Drive with a Modbus RTU interface are able to provide speed feedback to the BB Controller. That informatio...
- Fri Jul 29, 2022 12:07 pm
- Forum: Buildbotics Tech Support
- Topic: Sherline Spindle Tachometer & Speed Control
- Replies: 4
- Views: 10509
Re: Sherline Spindle Tachometer & Speed Control
Hi Fred, The Buildbotics Controller has a 0-10 Volt output available on the DB15 connector. I looked at the datasheet for KBIC speed controllers and it says that you can control the motor speed with a 0-9Volt isolated analog voltage. It says you should connect the 0-9Volt source between P2 and F-. T...
- Sat Jul 23, 2022 7:41 pm
- Forum: Buildbotics Tech Support
- Topic: 3D View and Zero Feed Rate
- Replies: 7
- Views: 12830
- Fri Jul 22, 2022 3:57 pm
- Forum: Buildbotics Tech Support
- Topic: 3D View and Zero Feed Rate
- Replies: 7
- Views: 12830
Re: 3D View and Zero Feed Rate
Try removing the G1 from the first line.
- Fri Jul 22, 2022 3:51 pm
- Forum: Buildbotics Tech Support
- Topic: 3D View and Zero Feed Rate
- Replies: 7
- Views: 12830
Re: 3D View and Zero Feed Rate
You must set the feed rate before executing a non-rapid move. Otherwise, the controller doesn’t know how fast to go during the move.
- Thu Jul 21, 2022 7:47 pm
- Forum: Buildbotics Tech Support
- Topic: 3D View and Zero Feed Rate
- Replies: 7
- Views: 12830
Re: 3D View and Zero Feed Rate
Making a non-rapid move with zero feed rate should cause an error because the command cannot be executed. It either doesn’t know how fast to go or it tries to move at zero speed.
- Sun Jul 17, 2022 2:50 pm
- Forum: Buildbotics Tech Support
- Topic: Heat Sink?
- Replies: 3
- Views: 9378
Re: Heat Sink?
The heat sink lays on top of the raspberry pi as shown. The white tape on the bottom should hold it in place. It conducts heat but does not conduct electricity. Make sure that no exposed aluminum on the heat sink is in direct contact with any of the components. The white grease on the top is heat gr...
- Sun Jul 17, 2022 2:41 pm
- Forum: Buildbotics Tech Support
- Topic: Need help setting my soft-limits
- Replies: 4
- Views: 11922
Re: Need help setting my soft-limits
Offsets are used to tell the controller where the work piece is located. You should place the work piece on the table, jog the bit into the x=0, y=0, z=0 position and then click the zero offsets button to tell the controller that is position (0,0,0). If you move the work piece, you will have to chan...